Optics · arXiv:2611.16497 v1 · submitted 12 Nov 2026 · 39 references
Design and optimization of multilevel zone plates for flying focus applications
The paper says
“Flying focus pulses, characterized by programmable velocities decoupled from the group velocity, offer remarkable potential for high-intensity laser-matter interactions. However, achieving low-cost manufacturing while simultaneously suppressing higher-order foci and maintaining high efficiency remains a key challenge.”
more of the abstract
Here, we propose a modulated width zone plate with 2M steps (MWZP-2MS). By employing Monte Carlo sampling of sinusoidal random widths, the MWZP-8S design statistically mimics a Gabor zone plate, suppressing higher-order foci by four orders of magnitude. Furthermore, the multilevel phase modulation converts opaque regions into constructive phase-shifting zones, significantly boosting the focusing efficiency to 73.7% when M = 3. Numerical simulations demonstrate that the focal velocity is flexibly tunable across subluminal and superluminal regimes while remaining stable over 100 Rayleigh lengths. This scalable and cost-effective scheme provides a robust platform for flying focus applications in EUV generation and X-ray optics.
from the abstract
Pith says
Machine review · deepseek-v4-flash · 13 Nov 2026 · what was read was not recorded · not checked by a person
It can be wrong. Challenge this review or reply to it.
Holds up, with conditions. A practical diffractive optic design for flying focus that combines two known ideas (random width modulation and multilevel phase) with clean simulations, but the suppression claim rests on an unquantified single-realization variance. This line is wrong
3 major objections · 4 minor
How often objections from reviews like this one are right: not yet measured
Not checked: figures, code, what the 39 references say.
The paper says, at Section 2.2.A, Section 3.2 (Fig. 5)
The review did not quote this passage.
Pith says: Objection 1 of 3 · major
The suppression of higher-order foci is derived from the expected transmittance of the random modulation, but a fabricated element is a single realization. The paper presents only one simulation (implied by Monte Carlo sampling) and does not quantify the variance of the higher-order intensity across different random seeds.
more of objection 1
Without a statistical bound (e.g., worst-case or typical suppression with confidence intervals), the central claim of 'four orders of magnitude suppression' is not supported for any individual device. The authors should provide multiple realizations or an analytical bound on the fluctuations.
The paper says, at Appendix C, Eqs. (35)-(36)
The review did not quote this passage.
Pith says: Objection 2 of 3 · major
The approximation δ ≈ |r^2/R1^2 - (2n-1)| is justified only for large n (outer zones). The paper does not assess the error introduced for small n (inner zones), where the zone widths are larger and the approximation is less accurate. Since the central zones contribute to the focal spot, this could affect the expected transmittance and the suppression of higher orders. An error analysis or justification that the approximation is acceptable for all zones is needed.
The paper says, at Section 3, Table 2 and Eq. (12)
The review did not quote this passage.
Pith says: Objection 3 of 3 · major
The focusing efficiency is computed using a variable aperture integration, and the authors state that 'the sampling pixels is increased to be 44800 in each side' for efficiency calculations. However, the numerical convergence of this efficiency with respect to pixel count and the effect of the random zone-width modulation on the integrated intensity are not discussed. The 73.7% value may depend sensitively on the specific random realization; a single value is insufficient to characterize the design's typical efficiency.
4 minor objections
The paper says, at Section 3
Pith says: minor objection 1 of 4
The sentence 'The number 7800 is chosen to qualify the stringent standard k0 w0 π f#' contains a grammatical error; 'qualify' should likely be 'satisfy' or 'meet'.
The paper says, at Figs. 10 and 11
Pith says: minor objection 2 of 4
The axis labels for z and t in Figs. 10 and 11 are given as 'z-f_1' and 't-f1/c'. This notation should be explained in the caption or main text to avoid confusion.
show 2 more
The paper says, at Eq. (7)
Pith says: minor objection 3 of 4
The sign in the expected transmittance expression (E[t_MWZP(r)] ≈ 0.5[1 - cos(π r^2 / R1^2)]) differs from the standard Gabor zone plate transmittance (0.5[1 + cos(...)]). The paper refers to a 'negative GZP' but does not discuss the implications of this sign for the focusing properties. A brief clarification would be helpful.
The paper says, at Section 2.2.A
Pith says: minor objection 4 of 4
The probability density ρ(s) = 0.5π cos[π(s-0.5)] is cited from Ref. [25]. However, the cumulative distribution function F(s) in Eq. (3) appears to be derived from this ρ, but the integral should yield F(s)=0.5+0.5 sin[π(s-0.5)]; the paper writes '0.5 sin[π(s-0.5)]+0.5', which is the same. This is fine, but the derivation of the expectation in Eq. (6) should be explicitly checked for consistency.
What would settle it
Generate 10 independent random MWZP-8S designs with N=1000 (different random seeds for sampling s_n from Eq.4). For each, compute the on-axis relative intensity R(z) under plane-wave illumination (as in Fig.5). Extract the relative intensity at the fifth-order focal position (f/5). Report the mean, standard deviation, and maximum across realizations. If the maximum fifth-order intensity exceeds 5×10⁻⁴, then the four-order suppression is not guaranteed for a single device; if all values remain below 2×10⁻⁴, the claim is robust to statistical fluctuations. Also compute the focusing efficiency (at 100 μm aperture) for each realization to assess performance stability.
from the skeptic's reading
How the review went
4 readings by deepseek-v4-flash · 13 Nov 2026
- Reader holds up, with conditions
- Skeptic partly agrees
- Editor wrote the verdict above
- Referee major revision: 3 major objections, 4 minor
Not run on this paper: the simulated authors' defence.
Pith did not check this review's objections against the paper.
The review in full
The review in brief, machine-written
Zhengkun Li et al. propose combining random width modulation (MWZP, from Zhang 2018) with multilevel phase steps to simultaneously suppress higher-order foci and boost efficiency in flying-focus zone plates. The simulations show MWZP-8S achieving 73.7% efficiency and ~4-order suppression of higher-order foci, which is a clear improvement over the binary-amplitude MWZP baseline. The engineering merit is real: the design uses standard lithographic fabrication, and the authors include a ±5% etch‑depth tolerance study (Fig. 12) that shows only an 11% efficiency drop. That is a practical, cost‑effective route for flying focus experiments.
What the paper does well: the mathematical derivation (Sec. 2.2.A, Appendix C) linking the random width modulation to the Gabor zone plate transmittance is correctly laid out. The simulation method (modified Fresnel integrals) is standard and appropriate. The parametric study of zone count, phase steps, and chirp is thorough (Figs. 7–9, Table 3). The authors also clearly note fabrication challenges (Sec. 4, line b245). Credit where due: this is a competent simulation study that extends a known concept to a relevant application.
Now the soft spots. The central claim – that higher-order foci are suppressed by four orders of magnitude – relies on the expected transmittance of the random‑width modulation (Eq. 7). But a fabricated device is a single random realization, not an ensemble average. The paper does not quantify the variance of the higher‑order intensity across realizations; Fig. 5 shows only one simulated intensity profile. The approximation for δ in Appendix C (Eqs. 35‑36) is valid only for large n, and the finite‑N error is not bounded. The stress‑test note is correct: without a worst‑case bound or a statistical characterization, the suppression claim is not fully supported for any single device. The paper acknowledges fluctuations (Fig. 8) but does not connect them to the higher‑order residual.
These are not fatal flaws – the design will still outperform an FZP – but they weaken the quantitative headline. A reader who needs guaranteed suppression (e.g., for a sensitive experiment) will want error bars.
Who this is for: experimentalists working on flying focus who want a low‑cost diffractive alternative to deformable‑mirror or echelon schemes. The paper deserves a serious referee because the idea is useful and the simulations are clean. I would ask the authors to provide either a bound on the variance (e.g., via Chebyshev or a small Monte Carlo over realizations) or a statement that the single‑realization fluctuation is negligible for N=1000. Without that, the paper is still publishable, but the suppression factor should be reported as a typical value, not a guaranteed floor.
Recommendation: conditionally accept, subject to the authors adding a quantitative analysis of single‑realization deviations for the higher‑order suppression.
The strongest objection
The paper's core argument (Section 2.2.A, Eq.7) shows that the expected transmittance of a random-width-modulated zone plate equals that of a Gabor zone plate, thereby eliminating higher-order foci in expectation. However, a fabricated device is a single random realization, not an ensemble average. For a finite number of zones (N=1000), the actual transmittance fluctuates around the expectation; these fluctuations produce residual higher-order diffraction that is not analyzed. The numerical simulations (Fig.5) present only one realization (implied by Monte Carlo sampling), so the reported suppression of higher-order foci by four orders of magnitude may not be representative of all possible realizations. The paper acknowledges that random modulation introduces 'fluctuations' in the efficiency derivative (Fig.8), but does not quantify the impact on higher-order intensity, nor does it bound the worst-case suppression. Without a statistical characterization, the central claim that MWZP-8S reliably suppresses higher-order foci by four orders of magnitude is not supported for any single device.
The reader's weakest assumption concerns the finite-N deviation of the average transmittance from the ideal Gabor zone plate, focusing on an unquantified error bound. My identified concern is complementary: even if the average is perfect, the single-realization variance is uncontrolled. This is a load-bearing point because the paper markets a single design (MWZP-8S) as achieving the reported suppression, but the design is inherently random. Without quantifying the spread, the headline result could be an optimistic outlier. The concrete test directly probes this by simulating multiple random seeds. The verdict remains unchanged (CONDITIONAL) because the reader already requested quantitative error analysis; adding a request for statistical robustness strengthens the condition without contradicting the reader. The paper's own simulation uses only one seed, and the data/code are not public, so the concern is unresolved. The test is computationally feasible (the authors already have the code) and would settle whether the claim is robust or lucky.
The referee's report
If fully validated, the MWZP-2^M S design would provide a cost-effective and fabrication-friendly diffractive optical element for producing flying focus pulses with simultaneously high efficiency and strong suppression of higher-order foci. This could benefit applications such as laser-wakefield acceleration, EUV generation, and X-ray optics where spatiotemporal control of the focal spot is critical. The theoretical connection between randomized zone widths and the Gabor zone plate is elegant, and the extension to multilevel phase steps is a natural way to overcome the efficiency limitation of binary designs.
Pith's reading of the paper (a machine's summary, not the authors')
This paper proposes a new diffractive optical element for generating flying focus pulses: a modulated width zone plate with up to eight discrete phase steps (MWZP-8S). The key idea is to randomize the widths of transparent zones via Monte Carlo sampling to statistically mimic a Gabor zone plate, which inherently has no higher-order foci. By converting opaque zones into phase-shifting regions through multilevel phase modulation, the focusing efficiency is dramatically improved. Numerical simulations show that the MWZP-8S suppresses higher-order foci by four orders of magnitude, achieves a focusing efficiency of 73.7%, and produces a flying focus with tunable subluminal and superluminal velocities stable over more than 100 Rayleigh lengths.
What carries the argument. The central machinery is the combination of two design principles: (1) Monte Carlo random sampling of zone widths to mimic the continuous sinusoidal transmittance of a Gabor zone plate, which eliminates higher-order foci by breaking long-range periodicity; and (2) multilevel phase modulation (specifically eight steps in the MWZP-8S) that converts opaque regions into constructive phase-shifting zones, boosting focusing efficiency to 73.7%. The random width distribution is given by Eq. (2) and the multilevel phase boundaries by Eq. (8). The modified Fresnel integrals (Appendix B) are used to simulate the propagation of chirped Gaussian pulses through the zone plate.
Core claim. The central claim is that a modulated width zone plate with eight phase steps (MWZP-8S) can simultaneously suppress higher-order foci and achieve high focusing efficiency for flying focus applications. The authors demonstrate through numerical simulations that the random width modulation breaks the strict radial periodicity responsible for higher-order foci, while the eight-level phase discretization concentrates energy into the first diffraction order. The result is a single dominant focal spot with higher-order foci suppressed by four orders of magnitude and a focusing efficiency of 73.7%, approximately 5.8 times that of the unmodulated binary MWZP. The design also supports flexible tuning of the focal velocity by adjusting the chirp of the incident pulse, with velocities ranging from subluminal to superluminal, and stability over more than 100 Rayleigh lengths.
The premise it rests on. The statistical equivalence between the random-width-modulated zone plate and a continuous Gabor zone plate relies on the number of zones N being sufficiently large to realize the expected transmittance via the law of large numbers; the paper does not provide a formal quantitative bound on the deviation from the ideal transmittance for finite N.
If the paper is right (Pith's inferences, not the authors')
The MWZP-8S design enables low-cost fabrication of diffractive optical elements for flying focus using standard semiconductor photolithography, as opposed to expensive diamond turning or electron-beam lithography.
With its high focusing efficiency (73.7%) and suppression of higher-order foci, the design is suitable for high-intensity laser-matter interactions requiring extended interaction lengths and precise velocity matching, such as laser-wakefield acceleration and EUV generation.
The flexibility to tune the focal velocity from subluminal to superluminal by simply adjusting the pulse chirp makes the design adaptable to a wide range of applications, including pump-probe synchronization and photon acceleration.
The robustness against ±5% etching depth errors (only 11% efficiency drop) suggests the design is practical for real manufacturing tolerances.
The random width modulation could be extended to other diffractive elements, such as beam shapers or vortex plates, to suppress unwanted diffraction orders while maintaining high efficiency.
A formal proof of the statistical equivalence with a bound on the deviation for finite N would strengthen the design's reliability, especially for applications requiring exact focal profiles.
Experimental validation using existing lithographic techniques for fused silica at 800 nm would be a natural next step; the paper's tolerance analysis suggests success is plausible.
The design could be adapted to X-ray wavelengths, where zone plates are the standard focusing optics, potentially enabling flying focus in the X-ray regime for novel imaging or pump-probe experiments.
Check this review
Pith stored no record of this review's passes and took no fingerprint of it. Reviews made by code from 13 Nov 2026 on carry both.
How often reviews like this one are right
Reviews like this one: written by deepseek-v4-flash, where what was read was not recorded.
How often objections from reviews like this one are right: not yet measured
Reviews by people
This review was written by a machine. No person has reviewed this paper on Pith yet. A scientist listed on Pith can review it for a fee, and their review is published here whatever it concludes.
The paper
Abstract
Flying focus pulses, characterized by programmable velocities decoupled from the group velocity, offer remarkable potential for high-intensity laser-matter interactions. However, achieving low-cost manufacturing while simultaneously suppressing higher-order foci and maintaining high efficiency remains a key challenge. Here, we propose a modulated width zone plate with 2M steps (MWZP-2MS). By employing Monte Carlo sampling of sinusoidal random widths, the MWZP-8S design statistically mimics a Gabor zone plate, suppressing higher-order foci by four orders of magnitude. Furthermore, the multilevel phase modulation converts opaque regions into constructive phase-shifting zones, significantly boosting the focusing efficiency to 73.7% when M = 3. Numerical simulations demonstrate that the focal velocity is flexibly tunable across subluminal and superluminal regimes while remaining stable over 100 Rayleigh lengths. This scalable and cost-effective scheme provides a robust platform for flying focus applications in EUV generation and X-ray optics.
The paper's own sentences, arranged, kept beside the review and separate from it. Each label is drawn from a closed vocabulary; the number beside it is the probability the classifier gave that label. No sentence in this record was written by a model.
abstract compiled · 2026-11-13
The authors' main claim, as the classifier picked it out 1.00
“This scalable and cost-effective scheme provides a robust platform for flying focus applications in EUV generation and X-ray optics.”
How the main claim is stated: asserted 0.99
What the abstract itself states, as probabilities: claims first 0.05 · states limitation 0.23 · human participants 0.01 · controlled comparison 0.09 · randomized assignment 0.01 · states quantitative result 0.99 · compares with prior results 0.28 · mentions code or data availability 0.02
The abstract, sentence by sentence
This table labels the abstract only (arXiv listing abstract v1). The number is the probability the classifier gave the label.
| Sentence | Role | The authors' own work | States the main conclusion | Strength |
|---|---|---|---|---|
| Flying focus pulses, characterized by programmable velocities decoupled from the group velocity, offer remarkable potential for high-intensity laser-matter interactions. | background 1.00 | 0.06 | 0.03 | asserted 0.85 |
| However, achieving low-cost manufacturing while simultaneously suppressing higher-order foci and maintaining high efficiency remains a key challenge. | gap 0.83 | 0.06 | 0.03 | asserted 1.00 |
| Here, we propose a modulated width zone plate with $2^{M}$ steps (MWZP-$2^{M}$S). | contribution 0.92 | 0.85 | 0.06 | asserted 0.92 |
| By employing Monte Carlo sampling of sinusoidal random widths, the MWZP-8S design statistically mimics a Gabor zone plate, suppressing higher-order foci by four orders of magnitude. | result 0.63 | 0.90 | 0.14 | asserted 1.00 |
| Furthermore, the multilevel phase modulation converts opaque regions into constructive phase-shifting zones, significantly boosting the focusing efficiency to 73.7$\%$ when $M=3$. | result 0.96 | 0.91 | 0.18 | asserted 1.00 |
| Numerical simulations demonstrate that the focal velocity is flexibly tunable across subluminal and superluminal regimes while remaining stable over 100 Rayleigh lengths. | result 1.00 | 0.92 | 0.13 | asserted 1.00 |
| This scalable and cost-effective scheme provides a robust platform for flying focus applications in EUV generation and X-ray optics. | interpretation 0.97 | 0.41 | 0.72 | asserted 0.99 |
What kind of paper the classifier reports this is: method or tool 0.98 · evidence from simulation or computation 1.00
What was examined, and what was not
Sources read
- arXiv listing abstract v1
Not examined
- full text
- figures and tables
- references and citing sentences
- relations to other papers
Levels run
- P abstract
Not run
- S sections
- T body sentences
- C citations
- R cross-paper relations
How the labels were made
Compiled by classifier-1.13.0 via TypeSafe API, question bank abstract-p1-20260923, 2026-11-13: 1 request, 5,626 input tokens.
Every quoted sentence on this record is the authors'. Every label is from Pith's closed vocabulary, with the probability shown beside it. This record as JSON
Figures (14)
Figures are the authors', reproduced from the paper.
References (39)
- [1] S. Akturk, X. Gu, P. Bowlan,et al., “Spatio-temporal couplings in ultrashort laser pulses,” J. Opt.12, 093001 (2010) on Pith
- [2] G. Zhu, J. van Howe, M. Durst,et al., “Simultaneous spatial and temporal focusing of femtosecond pulses,” Opt. Express13, 2153–2159 (2005) on Pith
- [3] M. Yessenov, B. Bhaduri, H. E. Kondakci,et al., “Classification of propagation-invariant space-time wave packets in free space: Theory and experiments,” Phys. Rev. A99, 023856 (2019) on Pith
- [4] G. Tóth, G. Polónyi, and J. Hebling, “Tilted pulse front pumping techniques for efficient terahertz pulse generation,” Light. Sci. & Appl.12, 256 (2023) on Pith
- [5] L. Rego, K. M. Dorney, N. J. Brooks,et al., “Generation of extreme-ultraviolet beams with time-varying orbital angular momentum,” Science364, eaaw9486 (2019) on Pith
- [6] A. Sainte-Marie, O. Gobert, and F. Quere, “Controlling the velocity of ultrashort light pulses in vacuum through spatio-temporal couplings,” Optica4, 1298–1304 (2017) on Pith
- [7] D.H.Froula,D.Turnbull,A.S.Davies,et al.,“Spatiotemporalcontroloflaserintensity,”Nat.Photonics12,262–265 (2018) on Pith
- [8] J. J. Pigeon, P. Franke, M. L. P. Chong,et al., “Ultrabroadband flying-focus using an axiparabola-echelon pair,” Opt. Express32, 576–585 (2024) on Pith
- [9] M.Piccardo,M.Cernaianu,J.Palastro,et al.,“Trendsinrelativisticlasermatterinteraction: thepromisesofstructured light,” Optica12, 732–752 (2025) on Pith
- [10] J. P. Palastro, J. L. Shaw, P. Franke,et al., “Dephasingless laser wakefield acceleration,” Phys. Rev. Lett.124, 134802 (2020) on Pith
- [11] C. Caizergues, S. Smartsev, V. Malka,et al., “Phase-locked laser-wakefield electron acceleration,” Nat. Photonics14, 475–479 (2020) on Pith
- [12] A. Debus, R. Pausch, A. Huebl,et al., “Circumventing the dephasing and depletion limits of laser-wakefield acceleration,” Phys. Rev. X9, 031044 (2019) on Pith
- [13] A. Kabacinski, E. Oliva, F. Tissandier, and et al., “Spatio-temporal couplings for controlling group velocity in longitudinally pumped seeded soft x-ray lasers,” Nat. Photonics17, 354–359 (2023) on Pith
- [14] J. P. Palastro, D. Turnbull, S.-W. Bahk,et al., “Ionization waves of arbitrary velocity driven by a flying focus,” Phys. Rev. A97, 033835 (2018) on Pith
- [15] D. Turnbull, P. Franke, J. Katz,et al., “Ionization waves of arbitrary velocity,” Phys. Rev. Lett.120, 225001 (2018) on Pith
- [16] P. Franke, D. Turnbull, J. Katz,et al., “Measurement and control of large diameter ionization waves of arbitrary velocity,” Opt. Express27, 31978–31988 (2019) on Pith
- [17] D. H. Froula, J. P. Palastro, D. Turnbull,et al., “Flying focus: Spatial and temporal control of intensity for laser-based applications,” Phys. Plasmas26, 032109 (2019) on Pith
- [18] S. W. Jolly, O. Gobert, A. Jeandet,et al., “Controlling the velocity of a femtosecond laser pulse using refractive lenses,” Opt. Express28, 4888–4897 (2020) on Pith
- [19] M. B. Fleming and M. C. Hutley, “Blazed diffractive optics,” Appl. Opt.36, 4635–4643 (1997) on Pith
- [20] M. V. Ambat, J. L. Shaw, J. J. Pigeon,et al., “Programmable-trajectory ultrafast flying focus pulses,” Opt. Express 31, 31354–31368 (2023) on Pith
show 19 more
- [21] H. S. Markland, J. Rosenbluth, R. Boni,et al., “Rapidly tunable ultrabroadband flying focus using adaptive optics and an axiparabola,” Opt. Lett.51, 676–679 (2026) on Pith
- [22] P. Blum, A. Puchert, E. Archer,et al., “Programmable focal elongation and shaping of high-intensity laser pulses using adaptive optics,” Opt. Lett.51, 9–12 (2026) on Pith
- [23] B. Z. J. Z. J. F. Xian ZHANG, Mingxu PIAO, “Progress in minimalist diffractive optical systems(invited),” Acta Photonica Sinica55, 0622001– (2026) on Pith
- [24] H. O. Sankur and M. E. Motamedi, “Micro-optics development in the past decade,” Proc. SPIE, Int. Soc. for Opt. Eng. SPIE4179, 30–55 (2000) on Pith
- [25] Q. Zhang, Q. Fan, Z. Yang,et al., “Toward binary gabor zone plate by modulating zones width,” Optik174, 387–393 (2018) on Pith
- [26] D. Gabor, “A new microscopic principle,” Nature161, 777–778 (1948) on Pith
- [27] G. Rogers, “Gabor diffraction microscopy: the hologram as a generalized zone-plate,” Nature166, 237 (1950) on Pith
- [28] E. D. Fabrizio, F. Romanato, M. Gentili,et al., “High-efficiency multilevel zone plates for kev x-rays,” Nature401, 895–898 (1999) on Pith
- [29] A.Kabacinski,E.Oliva,F.Tissandier,et al.,“Spatio-temporalcouplingsforcontrollinggroupvelocityinlongitudinally pumped seeded soft x-ray lasers,” Nat. Photonics17, 354–359 (2023) on Pith
- [30] S. C. Wilks, J. M. Dawson, and W. B. Mori, “Frequency up-conversion of electromagnetic radiation with use of an overdense plasma,” Phys. Rev. Lett.61, 337–340 (1988) on Pith
- [31] A. J. Howard, D. Turnbull, A. S. Davies,et al., “Photon acceleration in a flying focus,” Phys. Rev. Lett.123, 124801 (2019) on Pith
- [32] W. Feller,An Introduction to Probability Theory and its Applications, Vol. II(John Wiley and Sons, 1971), 2nd ed on Pith
- [33] Q. Zhang, Z. He, Z. Xie,et al., “Diffractive optical elements 75 years on: from micro-optics to metasurfaces,” Photonics Insights2, R09 (2023) on Pith
- [34] J. W. Goodman,Introduction to Fourier optics(McGraw-Hill, 1969) on Pith
- [35] M. Born and E. Wolf,Principles of Optics(Pergamon, Oxford, UK, 1980) on Pith
- [36] E. Gerstmayr, C. Mariani, R. Fitzgarrald,et al., “Experimental demonstration of flying-focus enhanced thomson scattering,” (2026) on Pith
- [37] I. H. Malitson, “Interspecimen comparison of the refractive index of fused silica,” J. Opt. Soc. Am.55, 1205–1209 (1965) on Pith
- [38] A. S. Morillo-Candas, S. Augustin, E. Prat,et al., “Coherent nonlinear x-ray four-photon interaction with core-shell electrons,” Nature649, 590–596 (2026) on Pith
- [39] K. Zhao and X. Zhong,Optics(Peking University Press, Beijing, 2008), revised edition ed on Pith
Challenges and discussion
Disagree with the review, or know something it missed? Leave a comment, or challenge this review formally: a challenge becomes a permanent entry in this paper's record, and its decision is published here.
Come back by email
A short list of the week's newly reviewed papers. Nothing is sent until you confirm from your inbox, and every email has a link that stops it. No account.
No comments yet.
Sign in to comment