Pith.

Robotics · arXiv:2610.02706 v1 · submitted 2 Oct 2026 · 37 references

AdaTempo: Learning Shared Relative Tempo from Demonstrations for Faster Robot Manipulation

Jiale Cao, Yike Niu, Zhengrong Xue, Huazhe Xu

The paper says

“Visuomotor policies trained via imitation learning often inherit the unnecessarily slow timing of teleoperated demonstrations. Yet uniform speedup is unreliable because different phases of a manipulation task tolerate acceleration differently.”

more of the abstract

In this work, we introduce AdaTempo, a self-supervised method that accelerates visuomotor policies by exploiting shared relative-tempo structure in demonstrations. AdaTempo establishes phase correspondence, aggregates the aligned relative tempo into a consensus, and maps it to a continuous speedup profile used to resample demonstrations into accelerated training trajectories. Training standard policies such as ACT or Diffusion Policy on these resampled trajectories directly embeds the desired tempo in the learned behavior, without runtime tempo selection or online retiming. Extensive evaluations show that AdaTempo achieves up to a 3.57 × speedup and yields a stronger success–speed trade-off than the original policies and representative acceleration baselines.

from the abstract

Pith says

Machine review · deepseek-v4-flash · 5 Oct 2026 · what was read was not recorded · not checked by a person

It can be wrong. Challenge this review or reply to it.

Holds up, with conditions. A clean, well-specified training-side speedup method with a genuinely new tempo cue, but the headline success-rate advantage over baselines is not yet above noise. This line is wrong

3 major objections · 3 minor

How often objections from reviews like this one are right: not yet measured

Are you an author? What you can do.

Not checked: figures, code, what the 37 references say.

The paper says, at Sec. IV-B, Table II

The review did not quote this passage.

Pith says: Objection 1 of 3 · major

The central success-speed trade-off claim is not statistically established. Success rates are means over only three seeds and no per-seed variance, confidence interval, or significance test is reported anywhere. On Insertion, the precision-critical task where the tempo cue should matter most, AdaTempo achieves 25.00% versus 23.33% for ACT and 18.00% for DemoSpeedup; over 300 rollouts that gap is about one standard error, i.e., compatible with chance.

more of objection 1

The sentence in Sec. IV-B that AdaTempo 'achieves the highest success on both Transfer Cube and Insertion' is therefore not supported at the task level. Please report per-seed results and confidence intervals for at least the headline tasks, and either add rollouts on Insertion or temper the claim.

The paper says, at Sec. IV-C, Table III

The review did not quote this passage.

Pith says: Objection 2 of 3 · major

The real-world aggregate gain is dominated by a single task and at least one task is a reversal within noise. Aggregating Table III, AdaTempo's +35 total successful trials relative to ACT consist of +27 from Conveyor Fast alone (29/30 vs 2/30); on Sorting, AdaTempo is worse than DemoSpeedup (14/30 vs 18/30) and no better than ACT (15/30), all within noise at n=30.

more of objection 2

The statement that AdaTempo 'achieves the best or tied-best success on four of the six tasks' should be accompanied by uncertainty bounds; at 30 trials per condition the binomial standard error is roughly 9 percentage points, which swallows several of the reported per-task differences.

The paper says, at Sec. III-B(b) and Sec. IV-A(c), Eq. (7)

The review did not quote this passage.

A classifier read this sentence of the paper as acknowledging the concern (probability 0.64):

“Relative tempo is an empirical cue rather than a direct es- timate of the maximum feasible speed.”

Pith says: Objection 3 of 3 · major

Eq. (7) is an assumption, not a derived result: consensus relative tempo m(p)q(p), which measures how much faster or slower demonstrators move in each phase relative to their own average, is asserted to be monotonically informative about how much that phase tolerates acceleration.

more of objection 3

The leave-one-out analysis in Sec. IV-D validates the reproducibility of the cue, which is a different property. The only end-to-end check of the Eq. (7) bridge is success rate, which -- per the two comments above -- is not yet distinguished from noise on the decisive tasks. Additionally, the absolute speedup level depends on the per-task bounds (c_min, c_max) selected with held-out validation rollouts; the authors acknowledge this in the conclusion ([b178]), but as a consequence the headline 3.57x is a tuned quantity rather than a parameter-free prediction. A concrete test would be to vary (c_min, c_max) on Insertion and show a monotone success degradation consistent with the phase-wise profile, or to report success at the same SOD for AdaTempo and DemoSpeedup.

3 minor objections

The paper says, at Sec. IV-A(d)

Pith says: minor objection 1 of 3

SOD is computed over successful rollouts only, with failures excluded. Since slower rollouts are more likely to fail for an accelerated policy, this metric is potentially favorable to the accelerated method; please state explicitly whether the same exclusion rule is applied to all baselines and, ideally, report SOD computed over all rollouts as a sensitivity check.

The paper says, at Abstract and Sec. I

Pith says: minor objection 2 of 3

The 'up to 3.57x speedup' headline is the Can task value from Table II and is conditional on the per-task (c_min, c_max) selection; consider stating in the abstract that the per-task bounds are selected with held-out validation rollouts so that readers are not misled about the strength of the prediction.

show 1 more

The paper says, at Sec. IV-A(c)

Pith says: minor objection 3 of 3

The hyperparameter list is complete, which is commendable, but the sentence reporting eta_i as '0.01 mediant,si di(t,s)' is hard to parse; a short clause explaining that this scales the penalty relative to the typical local cost would help reproducibility.

What would settle it

Recompute Tables II and III from per-seed success counts and report Wilson 95% (or bootstrapped binomial) intervals per task and method; state explicitly whether the Insertion 25.00%-vs-23.33% gap and the real-world Sorting 14/30-vs-15/30-vs-18/30 differences are resolvable above noise. Then recompute the aggregate real-world success rates (77.8% vs 58.3%) with Conveyor Fast removed, and report whether the claimed aggregate trade-off survives without the single dominant task. Publish these results as a supplementary table so the per-task reversals and the aggregate dependency are transparent.

from the skeptic's reading

How the review went

4 readings by deepseek-v4-flash · 5 Oct 2026

  1. Reader holds up, with conditions confidence moderate
  2. Skeptic partly agrees 30 s · 13,977 tokens read, 4,130 written
  3. Editor wrote the verdict above 34 s · 15,192 tokens read, 2,774 written
  4. Referee major revision: 3 major objections, 3 minor 24 s · 14,468 tokens read, 3,449 written

Not run on this paper: the simulated authors' defence.

Pith did not check this review's objections against the paper.

The review in full

The review in brief, machine-written

The thing to know: AdaTempo is a clean, well-specified training-side method, and the relative-tempo cue is genuinely distinct from DemoSpeedup, ESPADA, AutoSpeed, and SAIL. Episode-internal rank normalization, median consensus with MAD-based confidence, and virtual-time resampling hang together, and the leave-one-out Spearman analysis (0.861–0.952 with DTW vs 0.662–0.885 arc-length-only) is a real out-of-sample check that shared tempo structure exists. The ablations are coherent: consensus helps, confidence weighting helps, temporal regularization helps on Insertion. The arithmetic reproduces from the tables. The authors also state the main limitations themselves — the cue is empirical, not a feasibility estimate, and the bounds are selected per task on validation rollouts — so those are known conditions, not hidden flaws.

The soft spot, and it is the load-bearing one: the end-to-end claim that AdaTempo yields a stronger success–speed trade-off is not statistically established. No table reports per-seed variance or confidence intervals. On Insertion, the precision-critical task where the cue should matter most, AdaTempo's 25.00% vs ACT's 23.33% is about one standard error at 3 seeds × 100 rollouts — compatible with chance. Real-world Sorting is a reversal (14/30 vs DemoSpeedup's 18/30), again within noise at n=30. The aggregate real-world gain is dominated by Conveyor Fast (+27 successful trials of a +35 total). The conditional verdict is right, and the stress-test concern lands: Eq. (7), mapping consensus tempo to per-phase acceleration, is validated only by success rate, and that evidence is currently too weak to distinguish the mechanism from noise.

Two lesser issues. The per-task (c_min, c_max) tuning sets the absolute speedup, so "up to 3.57x" is conditional on task-specific validation selection; the authors acknowledge this, but the framing still overstates. And no code or data are released, which matters for a method paper whose value is largely in the pipeline.

Who this is for: anyone in the demonstration-speedup subfield, and people deploying imitation-learned policies in time-critical settings. It deserves a serious referee. The right outcome is major revision: variance reporting or confidence intervals on the headline comparisons, either automatic bound selection or a sensitivity analysis showing the result is not tuned into place, and released code and data. I would cite it for the cue and the consistency analysis regardless.

The strongest objection

The central claim that shared relative tempo yields a stronger success–speed trade-off rests on Eq. (7), which maps consensus relative tempo m(p)q(p) to per-phase acceleration. The only end-to-end check of this bridge is success rate, and that evidence is unquantified and, on the decisive task, within noise. On Insertion — the precision task where the tempo cue should matter most — AdaTempo achieves 25.00% vs ACT 23.33% and DemoSpeedup 18.00% (Table II); with 3 seeds × 100 rollouts, a 25%-vs-23.33% gap (roughly 75 vs 70 of 300) is about one standard error, i.e., compatible with chance. In the real world, Sorting is a reversal: AdaTempo 14/30 vs ACT 15/30 and DemoSpeedup 18/30 (Table III), again within noise at n=30. No table reports per-seed variance, confidence intervals, or tests, so several headline differences may be noise. The aggregate real-world gain (77.8% vs 58.3%) is dominated by the single Conveyor Fast task (+27 successful trials of a +35 total gain), and the per-task (c_min, c_max) bounds are selected on held-out validation rollouts (Sec. IV-A(c); authors acknowledge this in [b178]), so the reported 3.57x is conditional on task-specific tuning. These issues do not invalidate the reproducible-tempo mechanism (Fig. 5, leave-one-out correlations 0.861–0.952), but they fail to establish that the tempo cue beats baselines above noise.

The reader's stated weakest_assumption (Eq. (7) monotonicity: relative tempo as a proxy for acceleration tolerance) is real but is only load-bearing in the sense that its sole validation channel — end-to-end success rate — is statistically ungrounded. That merges the reader's concern (i) (no error bars) with the Eq. (7) bridge: the bridge can only be confirmed by success rates, and those rates are within noise precisely on Insertion, the task designed to exercise the precision-cautious phases the cue claims to protect. I disagree with the reader's weighting only in emphasis: the authors already acknowledge the bound-selection overfitting and the 'empirical cue, not direct estimate' caveat ([b175], [b178]), so those are acknowledged limitations rather than new findings; what remains unresolved is whether the success-rate evidence for the trade-off claim is real at all. The real-world aggregate is heavily dependent on a single task (Conveyor Fast, +27 of +35 total successful-trial gains), and the Sorting task is a reversal. Because the mechanism itself is independently supported by the leave-one-out reproducibility analysis and the ablations, and because the flaws are fixable with variance reporting and aggregate sensitivity checks, the correct disposition is CONDITIONAL, matching the reader; no verdict change is warranted, only reinforcement of the condition. REJECT would be premature since reproducibility and ablations provide genuine support, and ACCEPT is not justified while the headline comparisons may be within noise.

The referee's report

If the central claim holds, AdaTempo is a genuinely attractive method: it needs no auxiliary model, no runtime tempo selection, and no interaction-based optimization, and it produces a continuous, phase-dependent speedup profile from demonstrations alone. The manuscript has real strengths: the pipeline is fully specified; the reported arithmetic is internally consistent (the mean success of 75.5% and mean SOD of 2.83x reproduce from Table II, and the 2.02x/1.95x real-world speedups reproduce from Table III); and the leave-one-out consistency analysis (Fig. 5) is a genuine out-of-sample check showing that the relative-tempo cue is reproducible across demonstrations and that DTW alignment improves it on all 11 tasks (correlations 0.661-0.885 arc-length only, 0.861-0.952 DTW-aligned). The load-bearing gap is that the link from reproducible cue to acceleration tolerance, encoded by Eq. (7), is validated only by success rates, and those are reported without variance, confidence intervals, or tests, with the decisive precision task within noise.

Pith's reading of the paper (a machine's summary, not the authors')

This paper tries to establish that teleoperated demonstrations of a manipulation task contain a reusable, self-supervised timing cue: within each episode, some phases are consistently executed faster and others (grasping, insertion) more slowly, and this relative-tempo pattern is shared across demonstrators. AdaTempo extracts that pattern by aligning demonstrations to a canonical phase via dynamic time warping, ranking each episode's phase-local tempo to strip out absolute speed, and aggregating the ranked profiles into a consensus weighted by disagreement-based confidence, which it maps to a continuous speedup profile. It then resamples the demonstrations offline by that profile and trains standard policies (action-chunk transformers such as ACT and the Diffusion Policy backbone) on the accelerated trajectories, embedding the tempo so that deployment needs no runtime module or online retiming. If the claim holds, demonstration structure alone can decide both how much and where to accelerate, and the paper reports up to $3.57\times$ speedup over demonstrations, the highest average simulation success ($75.5\%$ at a mean $2.83\times$ speedup-over-demonstration), and a real-world aggregate success rise from $58.3\%$ to $77.8\%$ while completing tasks $2.02\times$ faster on average. A sympathetic reader would care because this is an offline, training-side acceleration that adds no extra machinery at execution time, unlike prior adaptive methods.

What carries the argument. The load-bearing object is the consensus relative-tempo profile $m(p)q(p)$: the across-demonstration median of ranked, phase-local tempo ($m$) weighted by a MAD-derived confidence ($q$) evaluated at a canonical phase $p\in[0,1]$. The episode-internal ranking of inverse phase occupancy does the essential work — normalizing tempo by rank rather than absolute speed isolates how tempo varies within a demonstration instead of how fast the whole episode runs. This profile is converted to a continuous speedup $c_i(t) = c_{\min} + (c_{\max}-c_{\min})\,m(p_i(t))\,q(p_i(t))$, regularized by a lookahead soft minimum that anticipates cautious phases and asymmetric slew limits that let the profile slow down faster than it speeds up, then applied through offline virtual-time resampling to produce the accelerated training dataset. Phase correspondence itself is established by progress-regularized monotonic DTW to a canonical medoid, using normalized cumulative motion arc length as the progress descriptor that prevents implausible matches between distant task stages.

Core claim. The central claim is that cross-demonstration relative tempo is a reproducible and informative cue for phase-dependent speedup. Concretely, AdaTempo shows that within each demonstration, faster phases occupy fewer timesteps, so ranking canonical-phase bins by inverse occupancy yields an episode-relative tempo that removes each demonstrator's global speed scale; aligning demonstrations with progress-regularized dynamic time warping to a medoid makes these profiles comparable at matched task progress, and agreement with the leave-one-out consensus reaches Spearman correlations of $0.861$–$0.952$ across all eleven tasks, improving on arc-length-only correspondence in every task. The paper then treats the consensus median $m(p)$ modulated by a median-absolute-deviation-based confidence $q(p)$ as a continuous speedup profile $c_i(t) = c_{\min} + (c_{\max}-c_{\min})\,m(p_i(t))\,q(p_i(t))$, smooths it with a lookahead soft minimum and asymmetric slew-rate limiting, and resamples each demonstration by advancing virtual source time so that denser samples fall in cautious phases. Training standard visuomotor policies on the resampled trajectories yields the reported success–speed trade-off: the highest average simulation success at a mean speedup comparable to the closest offline baseline, and the best or tied-best real-world success on four of six tasks.

The premise it rests on. The load-bearing premise is that the consensus relative tempo — how much slower or faster each phase is executed relative to a demonstration's own average — tracks how much that phase can be safely accelerated; reproducibility across demonstrators does not by itself establish that a cautious phase can actually be compressed, and the only end-to-end check is success rate, which is weak precisely on the precision-critical Insertion task ($25.00\%$ versus a $23.33\%$ baseline).

If the paper is right (Pith's inferences, not the authors')

Uniform speedup is a suboptimal lever: because phases tolerate acceleration differently, the phase-aware consensus reaches a mean $2.83\times$ SOD at $75.5\%$ success in simulation, versus DemoSpeedup's comparable $2.86\times$ at a lower $68.1\%$.

The tempo schedule is embedded in training data, so deployment is standard policy inference with no tempo-selection module or online retiming; only low-level control gains are raised for tracking.

The approach transfers across policy backbones, improving or matching baselines on both ACT-based ALOHA tasks and Diffusion-Policy-based robomimic tasks.

Over the real-world suite, AdaTempo raises aggregate success from $58.3\%$ (ACT) to $77.8\%$ at a $2.02\times$ mean completion-time speedup, with the largest reliability gain on the time-critical Conveyor Fast task ($29/30$ versus $2/30$ for ACT).

The relative-tempo structure is reproducible across demonstrators, with pairwise Spearman correlations of $0.983$, $0.941$, and $0.955$ on Conveyor Fast, supporting its use as a self-supervised supervisory signal.

The MAD-derived confidence $q(p)$ could serve as a phase-wise risk estimate on its own: phases where demonstrations disagree about tempo are plausibly the risky ones to compress, so the same consensus could gate acceleration limits without any reinforcement learning or simulator.

Because the acceleration bounds $(c_{\min}, c_{\max})$ are chosen per task from validation rollouts, the reported speedup level partly depends on that selection; a natural test is whether bounds can be predicted from demonstration statistics (overall speed, gripper-dwell indicators of precision) to make the pipeline fully automatic, a direction the paper flags as future work.

The paper states that a single medoid and consensus may fail when demonstrations contain qualitatively different strategies; if so, applying the same machinery within strategy clusters should raise confidence and tempo accuracy, which predicts a testable gain from strategy-aware clustering.

AdaTempo accelerates at training time, so it is arguably complementary to runtime adaptive methods: an offline schedule embedded in the policy plus a lightweight runtime feasibility check could combine the reliability reported here with the online adaptation that a fixed learned tempo cannot provide.

Check this review

Pith stored no record of this review's passes and took no fingerprint of it. Reviews made by code from 13 Nov 2026 on carry both.

How often reviews like this one are right

Reviews like this one: written by deepseek-v4-flash, where what was read was not recorded.

How often objections from reviews like this one are right: not yet measured

Every value above, in the review's public record (JSON)

Reviews by people

This review was written by a machine. No person has reviewed this paper on Pith yet. A scientist listed on Pith can review it for a fee, and their review is published here whatever it concludes.

Request a human review

How Pith checks papers · The full audit of this paper

The paper

Abstract

Visuomotor policies trained via imitation learning often inherit the unnecessarily slow timing of teleoperated demonstrations. Yet uniform speedup is unreliable because different phases of a manipulation task tolerate acceleration differently. In this work, we introduce AdaTempo, a self-supervised method that accelerates visuomotor policies by exploiting shared relative-tempo structure in demonstrations. AdaTempo establishes phase correspondence, aggregates the aligned relative tempo into a consensus, and maps it to a continuous speedup profile used to resample demonstrations into accelerated training trajectories. Training standard policies such as ACT or Diffusion Policy on these resampled trajectories directly embeds the desired tempo in the learned behavior, without runtime tempo selection or online retiming. Extensive evaluations show that AdaTempo achieves up to a 3.57 × speedup and yields a stronger success–speed trade-off than the original policies and representative acceleration baselines.

The paper's own sentences, arranged, kept beside the review and separate from it. Each label is drawn from a closed vocabulary; the number beside it is the probability the classifier gave that label. No sentence in this record was written by a model.

abstract compiled · 2026-10-05

The authors' main claim, as the classifier picked it out 0.99

“Extensive evaluations show that AdaTempo achieves up to a $3.57\times$ speedup and yields a stronger success--speed trade-off than the original policies and representative acceleration baselines.”

How the main claim is stated: asserted 1.00

What the abstract itself states, as probabilities: claims first 0.06 · states limitation 0.12 · human participants 0.20 · controlled comparison 0.95 · randomized assignment 0.02 · states quantitative result 0.99 · compares with prior results 0.96 · mentions code or data availability 0.03

The abstract, sentence by sentence

This table labels the abstract only (arXiv listing abstract v1). The number is the probability the classifier gave the label.

SentenceRoleThe authors' own workStates the main conclusionStrength
Visuomotor policies trained via imitation learning often inherit the unnecessarily slow timing of teleoperated demonstrations. background 0.98 0.06 0.03 asserted 0.96
Yet uniform speedup is unreliable because different phases of a manipulation task tolerate acceleration differently. background 0.65 0.13 0.03 asserted 0.99
In this work, we introduce AdaTempo, a self-supervised method that accelerates visuomotor policies by exploiting shared relative-tempo structure in demonstrations. contribution 1.00 0.90 0.23 asserted 1.00
AdaTempo establishes phase correspondence, aggregates the aligned relative tempo into a consensus, and maps it to a continuous speedup profile used to resample demonstrations into accelerated training trajectories. method 1.00 0.91 0.07 asserted 1.00
Training standard policies such as ACT or Diffusion Policy on these resampled trajectories directly embeds the desired tempo in the learned behavior, without runtime tempo selection or online retiming. method 0.96 0.78 0.12 asserted 1.00
Extensive evaluations show that AdaTempo achieves up to a $3.57\times$ speedup and yields a stronger success--speed trade-off than the original policies and representative acceleration baselines. result 1.00 0.96 0.78 asserted 1.00

What kind of paper the classifier reports this is: method or tool 1.00 · evidence from observation or experiment 0.97

What was examined, and what was not

Sources read

  • arXiv listing abstract v1

Not examined

  • full text
  • figures and tables
  • references and citing sentences
  • relations to other papers

Levels run

  • P abstract

Not run

  • S sections
  • T body sentences
  • C citations
  • R cross-paper relations

How the labels were made

Compiled by classifier-1.13.0 via TypeSafe API, question bank abstract-p1-20260923, 2026-10-05: 1 request, 4,947 input tokens.

Every quoted sentence on this record is the authors'. Every label is from Pith's closed vocabulary, with the probability shown beside it. This record as JSON

Figures (5)
Figure 1 of the paper
Figure 1. Overview. Left: Demonstrations exhibit shared phase-dependent relative-tempo patterns, with faster motion in casual phases and slower motion in precision-critical phases. AdaTempo exploits this structure to enable non-uniform acceleration across task progress. Right: On a fast conveyor-belt task, AdaTempo keeps pace with the production line and successfully grasps fast-moving objects that the ACT baseline frequently misses. Abstract— Visuomotor policies trained via imitation learning often inherit the unnecessarily slow timing of teleoperated demonstrations. Yet uniform speedup is…
Figure 2 of the paper
Figure 2. Pipeline. Demonstrations with different durations are aligned to a canonical phase. Their relative-tempo consensus and agreement determine a continuous speedup profile, which resamples the demonstrations for standard visuomotor policy training. A. Phase-Aligned Relative Tempo a) Motion progress and canonical reference: For each demonstration, we first Gaussian-smooth the continuous robot-target channels along time. From these smoothed tar￾gets, we construct a progress descriptor ui,t and an alignment descriptor yi,t. The progress descriptor retains the continuous arm-motion…
Figure 3 of the paper
Figure 3. Simulation tasks. We evaluate five tasks from ALOHA and Robomimic. Transfer Cube and Insertion emphasize coordinated bimanual manipulation, while Can, Lift, and Square cover single-arm grasping and precise object manipulation. time, ACT-2× temporally downsamples the original ACT action chunk by 2× without retraining the policy, whereas DP-Fast executes predicted trajectories at a higher fixed command rate. DemoSpeedup provides the closest offline resampling baseline, while SAIL represents adaptive runtime acceleration and uses its prescribed time-varying execution intervals and…
Figure 4 of the paper
Figure 4. Real-world evaluation tasks. We consider six tasks covering complementary manipulation challenges. Among them, Sorting and Folding emphasize long-horizon, multi-stage manipulation; Pouring and Stacking Cups require precise coordination and spatial alignment; and Conveyor Fast stresses time￾critical manipulation, requiring the robot to keep pace with fast-moving objects
Figure 5 of the paper
Figure 5. Relative-tempo consistency. (a) Demonstrator-wise consensus profiles on Conveyor Fast from three demonstrators, together with the pooled consensus. (b) Median and interquartile range of leave-one-out Spearman correlations across demonstrations on all 11 tasks. and asymmetric slew limits, directly using the resulting instantaneous speed curve. RBD-style augmentation adds offset resampling variants to improve source-state coverage, following the replicate-before-downsample principle used for integer-rate downsampling [7], [28]. Table IV summarizes the results. Cross-demonstration…

Figures are the authors', reproduced from the paper.

References (37)
  1. [1] T. Z. Zhao, V . Kumar, S. Levine, and C. Finn, “Learning fine-grained bimanual manipulation with low-cost hardware,” inProceedings of Robotics: Science and Systems, 2023 on Pith
  2. [2] C. Chi, Z. Xu, S. Feng, E. Cousineau, Y . Du, B. Burchfiel, R. Tedrake, and S. Song, “Diffusion policy: Visuomotor policy learning via action diffusion,” inProceedings of Robotics: Science and Systems, 2023 on Pith
  3. [3] Y . Ze, G. Zhang, K. Zhang, C. Hu, M. Wang, and H. Xu, “3D Diffusion Policy: Generalizable visuomotor policy learning via simple 3d representations,” inProceedings of Robotics: Science and Systems, 2024 on Pith
  4. [4] D. Ghosh, H. R. Walke, K. Pertsch, K. Black, O. Mees, S. Dasari, J. Hejna, T. Kreiman, C. Xu, J. Luo, Y . L. Tan, L. Y . Chen, Q. Vuong, T. Xiao, P. R. Sanketi, D. Sadigh, C. Finn, and S. Levine, “Octo: An open-source generalist robot policy,” inProceedings of Robotics: Scienc... on Pith
  5. [5] M. J. Kim, K. Pertsch, S. Karamcheti, T. Xiao, A. Balakrishna, S. Nair, R. Rafailov, E. P. Foster, P. R. Sanketi, Q. Vuong, T. Kol- lar, B. Burchfiel, R. Tedrake, D. Sadigh, S. Levine, P. Liang, and C. Finn, “OpenVLA: An open-source vision-language-action model,” inProceedings... on Pith
  6. [6] K. Blacket al., “π 0: A vision-language-action flow model for general robot control,”arXiv preprint arXiv:2410.24164, 2024 on PithPith's reviewarXiv
  7. [7] L. Guo, Z. Xue, Z. Xu, and H. Xu, “DemoSpeedup: Accelerating visuomotor policies via entropy-guided demonstration acceleration,” inProceedings of the Conference on Robot Learning, ser. Proceedings of Machine Learning Research, vol. 305, 2025, pp. 599–609 on Pith
  8. [8] N. R. Arachchige, Z. Chen, W. Jung, W. C. Shin, R. Bansal, P. Barroso, Y . H. He, Y . C. Lin, B. Joffe, S. Kousik, and D. Xu, “SAIL: Faster-than-demonstration execution of imitation learning policies,” in Proceedings of the Conference on Robot Learning, ser. Proceedings of Mac... on Pith
  9. [9] D. D. Yuan, T. Z. Zhao, K. Burns, and C. Finn, “SpeedTuning: Speed- ing up policy execution with lightweight reinforcement learning,” in Proceedings of the IEEE International Conference on Robotics and Automation, 2025, pp. 1184–1192 on Pith
  10. [10] S. Kim, J. Kim, and J. Lim, “Time optimal execution of action chunk policies beyond demonstration speed,” inInternational Conference on Learning Representations, 2026 on Pith
  11. [11] T. Nam, J. Cho, Y . Jang, and S. J. Hwang, “SpeedAug: Policy acceleration via tempo-enriched policy and reinforcement-learning fine-tuning,”arXiv preprint arXiv:2512.00062, 2025 on PithPith's reviewarXiv
  12. [12] R. A. Schmidt, “The search for invariance in skilled movement behavior,”Research Quarterly for Exercise and Sport, vol. 56, no. 2, pp. 188–200, 1985 on Pith
  13. [13] M. Shridhar, L. Manuelli, and D. Fox, “Perceiver-actor: A multi- task transformer for robotic manipulation,” inProceedings of the Conference on Robot Learning, 2022 on Pith
  14. [14] A. Brohanet al., “RT-1: Robotics transformer for real-world control at scale,”arXiv preprint arXiv:2212.06817, 2022 on PithPith's reviewarXiv
  15. [15] B. Zitkovichet al., “RT-2: Vision-language-action models transfer web knowledge to robotic control,” inProceedings of the Conference on Robot Learning, ser. Proceedings of Machine Learning Research, vol. 229, 2023, pp. 2165–2183 on Pith
  16. [16] S. Liu, L. Wu, B. Li, H. Tan, H. Chen, Z. Wang, K. Xu, H. Su, and J. Zhu, “RDT-1B: A diffusion foundation model for bimanual ma- nipulation,” inInternational Conference on Learning Representations, 2025 on Pith
  17. [17] Open X-Embodiment Collaboration, A. O’Neillet al., “Open X- embodiment: Robotic learning datasets and RT-X models,” inPro- ceedings of the IEEE International Conference on Robotics and Automation, 2024, pp. 6892–6903 on Pith
  18. [18] A. Khazatsky, K. Pertsch, S. Nairet al., “DROID: A large-scale in-the- wild robot manipulation dataset,” inProceedings of Robotics: Science and Systems, 2024 on Pith
  19. [19] A. Prasad, K. Lin, J. Wu, L. Zhou, and J. Bohg, “Consistency policy: Accelerated visuomotor policies via consistency distillation,” inProceedings of Robotics: Science and Systems, 2024 on Pith
  20. [20] G. Lu, Z. Gao, T. Chen, W. Dai, Z. Wang, and Y . Tang, “ManiCM: Real-time 3d diffusion policy via consistency model for robotic manipulation,”arXiv preprint arXiv:2406.01586, 2024 on PithPith's reviewarXiv
show 17 more
  1. [21] K. Pertsch, K. Stachowicz, B. Ichter, D. Driess, S. Nair, Q. Vuong, O. Mees, C. Finn, and S. Levine, “FAST: Efficient action tokenization for vision-language-action models,”arXiv preprint arXiv:2501.09747, 2025 on PithPith's reviewarXiv
  2. [22] K. Black, M. Galliker, and S. Levine, “Real-time execution of action chunking flow policies,” inAdvances in Neural Information Processing Systems, vol. 38, 2025 on Pith
  3. [23] H. Park, D. Lim, S. Kim, and S. Park, “Proleptic temporal ensemble for improving the speed of robot tasks generated by imitation learning,” arXiv preprint arXiv:2410.16981, 2024 on PithPith's reviewarXiv
  4. [24] Z. Wu, J. Ye, Z. Zhang, Y . Sun, H. Lin, J. Luo, H. Ren, L. Yuan, and Y . Yu, “Speedup patch: Learning a plug-and-play policy to accelerate embodied manipulation,”arXiv preprint arXiv:2603.20658, 2026 on PitharXiv
  5. [25] N. Masuya, S. Sakaino, and T. Tsuji, “Variable-frequency imitation learning for variable-speed motion,” inIEEE International Conference on Mechatronics, 2025, pp. 1–6 on Pith
  6. [26] D. Jing, J. Nie, T. Zhang, J. Liu, H. Yao, Z. Lu, and M. Ding, “Tem- poVLA: Learning speed-controllable vision-language-action policies,” arXiv preprint arXiv:2606.06491, 2026 on PithPith's reviewarXiv
  7. [27] X. Han, H. Xiong, H. Chen, C. Liu, A. Torralba, Y . Zhu, and Y . Du, “B-spline policy: Accelerating manipulation policies via b- spline action representations,”arXiv preprint arXiv:2607.09648, 2026 on PithPith's reviewarXiv
  8. [28] B. Kim, J. Pahk, C. Lee, J. Kim, J. Lee, T. T. Kim, K. Shim, J. K. Lee, and B.-T. Zhang, “ESPADA: Execution speedup via semantics aware demonstration data downsampling for imitation learning,”arXiv preprint arXiv:2512.07371, 2025 on PithPith's reviewarXiv
  9. [29] R. R. Sanchez, D. J. Evans, D. P. Losey, and S. Jain, “VOLT: Vision and language trajectory segmentation for faster-than-demonstration policies,”arXiv preprint arXiv:2606.06323, 2026 on PithPith's reviewarXiv
  10. [30] M. Dai, G. Peng, Y . Bai, F. Yan, C. Chen, L. Liu, L. Lin, and X. Wu, “SkiP: When to skip and when to refine for efficient robot manipulation,”arXiv preprint arXiv:2605.15536, 2026 on PithPith's reviewarXiv
  11. [31] Q. Hu, Z. Qiu, J. Zhao, Z. Gan, and W. Ding, “AutoSpeed: Annotation- free stage-adaptive motion speed learning for robot manipulation,” in European Conference on Computer Vision, 2026 on Pith
  12. [32] H. Sakoe and S. Chiba, “Dynamic programming algorithm optimiza- tion for spoken word recognition,”IEEE Transactions on Acoustics, Speech, and Signal Processing, vol. 26, no. 1, pp. 43–49, 1978 on Pith
  13. [33] G. Braglia, D. Tebaldi, A. E. Lazzaretti, and L. Biagiotti, “Arc-length- based warping for robot skill synthesis from multiple demonstrations,” arXiv preprint arXiv:2410.13322, 2024 on PitharXiv
  14. [34] J. J. Summers, “The role of timing in motor program representation,” Journal of Motor Behavior, vol. 7, no. 4, pp. 229–241, 1975 on Pith
  15. [35] D. C. Shapiro, R. F. Zernicke, R. J. Gregor, and J. D. Diestel, “Evidence for generalized motor programs using gait pattern analysis,” Journal of Motor Behavior, vol. 13, no. 1, pp. 33–47, 1981 on Pith
  16. [36] C. G. Atkeson and J. M. Hollerbach, “Kinematic features of unre- strained vertical arm movements,”The Journal of Neuroscience, vol. 5, no. 9, pp. 2318–2330, 1985 on Pith
  17. [37] A. Mandlekar, D. Xu, J. Wong, S. Nasiriany, C. Wang, R. Kulkarni, L. Fei-Fei, S. Savarese, Y . Zhu, and R. Mart´ın-Mart´ın, “What matters in learning from offline human demonstrations for robot manipula- tion,” inConference on Robot Learning, 2021 on Pith
Cited by 1 Pith paper

Challenges and discussion

Disagree with the review, or know something it missed? Leave a comment, or challenge this review formally: a challenge becomes a permanent entry in this paper's record, and its decision is published here.

No comments yet.

Sign in to comment